etap copy???
Posted: 12 Jul 2013, 20:49hi all is this a copy of thw etap2hw http://www.ebay.co.uk/itm/DLS-EchoTap-1 ... 51af45eff5 peter
Page 1 of 1
Posted: 12 Jul 2013, 20:49Re: etap copy???
Posted: 12 Jul 2013, 22:52No, it doesn't seem like a copy of the eTap2hw
Re: etap copy???
Posted: 13 Jul 2013, 09:34Look here : http://www.dlseffects.com/echotap.php
Just one of those echo box more or less intended to emultate the Echoplex. Not at all intended to emulate the vintage Meazzi...
Didier
Just one of those echo box more or less intended to emultate the Echoplex. Not at all intended to emulate the vintage Meazzi...
Didier
Re: etap copy???
Posted: 13 Jul 2013, 14:30Yanks are aware of eTAP HW and further product development & evaluation in progress. Just a matter of time
Bri
Bri
Re: etap copy???
Posted: 13 Jul 2013, 20:33ok thanks for replys. peter
Re: etap copy???
Posted: 14 Jul 2013, 15:19There are a group of people working on automation for the EtapHw already, I have all the bits to do it, but my first
one will be a hybrid version of Pancho's Etap...
That's one good thing about the Etap basic system it's fairly cheap so not too expensive to make more than one!!
one will be a hybrid version of Pancho's Etap...
That's one good thing about the Etap basic system it's fairly cheap so not too expensive to make more than one!!
Re: etap copy???
Posted: 14 Jul 2013, 18:19Amanda wrote:There are a group of people working on automation for the EtapHw already, I have all the bits to do it, but my first
one will be a hybrid version of Pancho's Etap...
That's one good thing about the Etap basic system it's fairly cheap so not too expensive to make more than one!!
hi amanda i would be keen to be kept up to date on how that project progress`s if you decide to produce any. thanks peter
Re: etap copy???
Posted: 15 Jul 2013, 20:44Automation is already implemented! The application called 'automation' is based on Johan's program and extended by Philip and Steve. Presently the 'automation' is build around my universal I/O board that takes a couple of incarnations of his software.
My recommendation is to use the latest 'automation' since it is not only very advanced but also promoted to 'single point design' making it much easier to support since one configuration needs to be managed. A write-up procedure to build it is not yet available but possible available when the temperature drops and leaves are disconnecting from the trees. Some 'early adaptors' did build based on some schematics and handholding.
There are sufficient boards available to support about 12 implementations ( 3 are assigned already) before a move to a vendor is started.
Piet
My recommendation is to use the latest 'automation' since it is not only very advanced but also promoted to 'single point design' making it much easier to support since one configuration needs to be managed. A write-up procedure to build it is not yet available but possible available when the temperature drops and leaves are disconnecting from the trees. Some 'early adaptors' did build based on some schematics and handholding.
There are sufficient boards available to support about 12 implementations ( 3 are assigned already) before a move to a vendor is started.
Piet
Re: etap copy???
Posted: 15 Jul 2013, 20:45Detailed Infinity wrote:Yanks are aware of eTAP HW and further product development & evaluation in progress. Just a matter of time
Bri
Bri,
There is presently one stompox build in the UK that's fortcoming. My code is also used by a firm in NY to be implemented into synth units.
Piet